8MM FORUM WORLDWIDE https://www.8mmforumworldwide.com/ |
|
Elmo 16-CL/Kodak Ektagraphic CT1000 sound issue https://www.8mmforumworldwide.com/viewtopic.php?f=13&t=2354 |
Page 1 of 2 |
Author: | Ken Segal [ Mon Feb 12, 2018 9:12 pm ] |
Post subject: | Elmo 16-CL/Kodak Ektagraphic CT1000 sound issue |
Hello. I recently acquired Kodak CT1000 (rebranded Elmo 16-CL). It's been in a garage for a very long time. I evicted the spiders, vacuumed and blew out both sides. I cleaned and greased it. I replaced the melted rubber rollers with new ones from a vendor on eBay. I replaced the bulb and replaced the fuses. I cleaned off the sound drum, head and lens. The exciter lamp lights. The amp makes noise, but no sound. But! I can hear the sound (in reverse) when I play backwards. Then, when switched to forward, the sound can be heard for a few seconds until the projector runs smoothly. Then just a hum. I also tried an external speaker. No difference. Any suggestions? |
Author: | Richard C Patchett [ Tue Feb 13, 2018 12:28 pm ] |
Post subject: | Re: Elmo 16-CL/Kodak Ektagraphic CT1000 sound issue |
Greetings Sounds like (no punt interned) The large Flange roller maybe out of adjustment and not moving the film by the sound light Drum Try by using your finger to push the film lightly before the large roller back and forth (in and out ) ( what type of rollers did you get from Flea bay Rubber or plastic ? Also on the flange roller they made 2 different ones Spring loaded and non spring loaded Hope this helps RC |
Author: | Ken Segal [ Tue Feb 13, 2018 2:10 pm ] |
Post subject: | Re: Elmo 16-CL/Kodak Ektagraphic CT1000 sound issue |
They're plastic rollers and I purchased them here. https://www.ebay.com/itm/16MM-PROJECTOR ... SwwE5WYbni |
Author: | Ken Segal [ Tue Feb 13, 2018 2:14 pm ] |
Post subject: | Re: Elmo 16-CL/Kodak Ektagraphic CT1000 sound issue |
They came with very precise instructions https://www.dropbox.com/s/ofu7eevdo4qx2 ... M.jpg?dl=0 |
Author: | Richard C Patchett [ Tue Feb 13, 2018 2:19 pm ] |
Post subject: | Re: Elmo 16-CL/Kodak Ektagraphic CT1000 sound issue |
Greetings Have you Tried moving the film yet ? Have you looked at the flange roller Old and new for spring type? I prefer the rubber ones a little more costly but wont scratch the film Did the sound work before you replaced the rollers RC |
Author: | Ken Segal [ Tue Feb 13, 2018 2:21 pm ] |
Post subject: | Re: Elmo 16-CL/Kodak Ektagraphic CT1000 sound issue |
Here's what the projector looks like post installation of the new rollers https://www.dropbox.com/s/kzaw6wx5fh4ba ... M.jpg?dl=0 |
Author: | Richard C Patchett [ Tue Feb 13, 2018 2:24 pm ] |
Post subject: | Re: Elmo 16-CL/Kodak Ektagraphic CT1000 sound issue |
Greetings Im trying to help Please answer my questions RC |
Author: | Ken Segal [ Tue Feb 13, 2018 2:35 pm ] |
Post subject: | Re: Elmo 16-CL/Kodak Ektagraphic CT1000 sound issue |
Did the test. You're correct. Alignment. Here's the video https://vimeo.com/255603499 By the way, I'm really appreciating the help SORRY, POSTED WRONG VIDEO. CORRECT LINK IS A COUPLE OF POSTS LATER |
Author: | Ken Segal [ Tue Feb 13, 2018 2:37 pm ] |
Post subject: | Re: Elmo 16-CL/Kodak Ektagraphic CT1000 sound issue |
Wrong video. Stand by. It takes a few minutes to load. I'd I Ike you're opinion on the actual test |
Author: | Ken Segal [ Tue Feb 13, 2018 2:41 pm ] |
Post subject: | Re: Elmo 16-CL/Kodak Ektagraphic CT1000 sound issue |
Also, I never tried the projector before I replaced the original rollers. They had turned to goo. Thanks for being patient. I'm in a very slow internet area. |
Page 1 of 2 | All times are UTC - 5 hours [ DST ] |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |